EverActive UC 4000 is a new, professional quality in universal chargers with simultaneous support for Ni-MH and Li-ion batteries. Our proposal features very precise charging programs perfectly tailored for each type of battery.
We invite you to check out the presentation of the everActive UC-4000 charger
Li-ion and LiFePO4 batteries are charged very precisely using the CC/CV method with a termination level of about 75 mA. This guarantees complete safety and full charging of each battery, even if it is heavily degraded or has a low capacity.
Ni-MH batteries are charged using the CC (constant current) method with very precise dV / PVD detection - charging is only completed after reaching the maximum voltage on the battery (the value of this voltage may vary for each battery).
The UC4000 charger focuses on maximum user convenience - the charger is extremely user-friendly and easy to operate.
An extraordinary compromise has been achieved - the charger features "only" 2 basic function buttons and 2 operating modes. Thoughtful operating modes make it so that despite these apparent limitations, the charger has practically the same, if not greater capabilities as models offering 4 separate operating modes.
| Key Features: - two main operating modes - charging (charge), discharging with refreshing (discharge), - in discharge mode, the battery is first discharged and then automatically charged to full - the charger independently remembers parameters and results for each process, - support for all popular cylindrical cells - also the so-called FLAT TOP - with a flat positive terminal, - 0.00V battery reanimation function - the charger can revive almost any battery, - microprocessor-controlled intelligent, precise CC/CV charging process for Li-ion / Li-FePO4 and CC with dV/PVD for Ni-MH, - support for protected (with PCB) and unprotected cells, also with flat positive terminal Flat Top, - adjustable charging current for lithium cells: 0.5A or 1A for each slot, for Ni-MH the charging current is 0.5A for each slot, - four independent charging channels with the ability to charge single batteries and unusual, odd combinations, - USB output 5V/1A for charging mobile devices - USB wall charger function (not Power Bank), - Capacity Review - discharging at 300 mA with capacity measurement and review function [mAh] - unique feature that allows reviewing two capacities [mAh] for each battery both from discharging and charging - allows assessing not only the battery capacity but also whether the battery has been properly charged, - complete set of protections: against overcharging, against excessive cell discharge, short circuit, overload, thermal, against reverse polarity of cells. |
 |
The charger allows charging and testing 1-4 pieces of lithium-ion, lithium iron phosphate, and nickel-metal hydride batteries in various sizes:
R6 AA, R03 AAA, R14 C (max. 2 pcs.), R20 D (max. 2 pcs.), 10440, 14500, 14650, 17500, 17670, 18350, 18500, 18650, 20700, 21700 - only unprotected, 22650, 25500 (max. 2 pcs.), 26500 (max. 2 pcs.), 26650 (max. 2 pcs.), 32650 (max. 2 pcs.), 33600 (max. 2 pcs.), 16340 R-CR123e.
The charger will handle any other cylindrical battery with a length of 32-71 mm and a maximum diameter of 33 mm.
All operating parameters can be viewed on an extremely readable, large, backlit LCD display.
The charger has a dual input voltage: 12V DC and 100-240V AC - the charger has an integrated power supply - the package includes a power cable, car adapter available separately.
- Li-ion batteries 3.6-3.7V, protected (with PCM/PCB)
- Li-ion batteries 3.6-3.7V, unprotected
- LiFePO4 Batteries
- Ni-MH batteries
- 12 V DC, 2.5 A maximum
- AC 100-240V, 50-60Hz
- Processor-controlled CC/CV for Li-ion/Li-FePO4
- Processor-controlled CC with -ΔV/0ΔV/PVD for Ni-MH
- Charge
- Refresh/Cycle(Rozładowanie z odświeżaniem)
- Adjustable - 500 mA / 1000 mA per channel / slot for Li-ion / Li-FePO4
- 500 mA per channel / slot for Ni-MH
- Li-ion 4.2V ±0,05V
- Li-FePO4 3.65V ±0.05V
- Ni-MH ~1.45V-1.55V dV/PVD
- 300
- Capacity review - extended measurement of battery capacity
- USB output 5V DC, 1A - USB wall charger function (requires the charger to be connected to the power supply)
- Before reloading
- Before over-discharging cells
- Against overload / short circuit
- Overload
- Thermal - before overheating of batteries
- Before reverse polarity of cells
- UC-4000 Charger, 1m Power Cable, User Manual
Universal power supply, USB-C PD voltage selector - DC 5V, 9V, 12V, 15V, 20V, 10 plugs, everActive AD-PD65
- one adapter that will replace a stack of chargers and power supplies at home, in the office, in service, and on the go!
- trigger, voltage selector, USB PD trigger
- universal adapter with selectable voltage 5V, 9V, 12V, 15V, 20V DC
- compatible with USB-C Power Delivery chargers and power banks - max 65W (3.25A/20V)
- 10 interchangeable DC plugs – fits laptops, chargers, cameras, printers, routers, and hundreds of other household devices
- built-in clear LED display with output voltage indication
- memory of the last selected voltage - safety during power outages!
- protection against accidental, rapid voltage changes during operation.
- Li-ion batteries 3.6-3.7V, protected (with PCM/PCB)
- Li-ion batteries 3.6-3.7V, unprotected
- LiFePO4 Batteries
- Ni-MH batteries
- 12 V DC, 2.5 A maximum
- AC 100-240V, 50-60Hz
- Processor-controlled CC/CV for Li-ion/Li-FePO4
- Processor-controlled CC with -ΔV/0ΔV/PVD for Ni-MH
- Charge
- Refresh/Cycle(Rozładowanie z odświeżaniem)
- Adjustable - 500 mA / 1000 mA per channel / slot for Li-ion / Li-FePO4
- 500 mA per channel / slot for Ni-MH
- Li-ion 4.2V ±0,05V
- Li-FePO4 3.65V ±0.05V
- Ni-MH ~1.45V-1.55V dV/PVD
- 300
- Capacity review - extended measurement of battery capacity
- USB output 5V DC, 1A - USB wall charger function (requires the charger to be connected to the power supply)
- Before reloading
- Before over-discharging cells
- Against overload / short circuit
- Overload
- Thermal - before overheating of batteries
- Before reverse polarity of cells
- UC-4000 Charger, 1m Power Cable, User Manual